Notice Type
Authorities/Other Agencies of State
Notice Title

Incorporation of Material by Reference in Safe Work Instruments

Pursuant to section 52 of the Legislation Act 2012, I, Nicole Rosie, Chief Executive, WorkSafe New Zealand, give notice that the standards listed in the Table are incorporated into the safe work instruments listed in the Table for the purposes of the Health and Safety at Work (Hazardous Substances) Regulations 2017.

All the safe work instruments listed in the Table were approved on 13 November 2017.

The Table sets out which standards are incorporated and the safe work instruments in which they are incorporated.

Copies of the standards incorporated may be purchased at the internet site addresses indicated in the Table:

Table

Standard

Safe work instrument

Place of purchase

AS/NZS 4766:2006

Polyethylene storage tanks for water and chemicals

Health and Safety at Work (Hazardous Substances—Polyethylene Above Ground Stationary Tanks for Diesel Fuel) Safe Work Instrument 2017

https://shop.bsigroup.com/

https://www.standards.govt.nz/

ASTM D1693-15

Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics

Health and Safety at Work (Hazardous Substances—Polyethylene Above Ground Stationary Tanks for Diesel Fuel) Safe Work Instrument 2017

https://www.astm.org/

BS EN 13341:2005+A1:2011

Static Thermoplastic Tanks for above ground storage of domestic heating oils, kerosene and diesel fuels — Blow moulded and rotationally moulded polyethylene tanks and rotationally moulded tanks made of anionically polymerized polyamide 6 — Requirements and test methods

Health and Safety at Work (Hazardous Substances—Polyethylene Above Ground Stationary Tanks for Diesel Fuel) Safe Work Instrument 2017

https://shop.bsigroup.com/

ISO 9001:2015

Quality Management Systems—Requirements

Health and Safety at Work (Hazardous Substances—Polyethylene Above Ground Stationary Tanks for Diesel Fuel) Safe Work Instrument 2017

https://www.iso.org/

https://www.standards.govt.nz/

UPSS Code of Practice for the Design, Installation, and Operation of Underground Petroleum Storage Systems (1st Edition) published in 1992 by the Occupational Safety and Health Service of the Department of Labour, New Zealand

Health and Safety at Work (Hazardous Substances­­-Management of Pre-2006 Stationary Container Systems up to 60,000 L) Safe Work Instrument 2017

https://worksafe.govt.nz/laws-and-regulations/standards/

ASTM D2563–08(2015)–Standard Practice for Classifying Visual Defects in Glass-Reinforced Plastic Laminate Parts.

Health and Safety at Work (Hazardous Substances—Design and Construction of Above Ground Stationary Tank to ULC-ORD-C80.1-2000) Safe Work Instrument 2017

https://www.astm.org/

ULC-ORD-C80.1-2000 Aboveground Non-Metallic Tanks for Fuel Oil

Health and Safety at Work (Hazardous Substances—Design and Construction of Above Ground Stationary Tank to ULC-ORD-C80.1-2000) Safe Work Instrument 2017

http://www.techstreet.com/standards/ulc-ord-c80-1-2000?product_id=1218151#jumps

ISO 11118:2015

Gas cylinders – Non-refillable metallic gas cylinders – Specification and test methods

Health and Safety at Work (Hazardous Substances—Specification of Standard Relating to Non-refillable Gas Containers) Safe Work Instrument 2017

https://www.iso.org

AS 1692:2006

Steel tanks for flammable and combustible liquids

Health and Safety at Work (Hazardous Substances—Reduced Secondary Containment for Certain Above Ground Stationary Tanks) Safe Work Instrument 2017

https://shop.bsigroup.com/

SwRI 93-01

Testing Requirements for Protected Aboveground Flammable Liquid/Fuel Storage Tanks

Health and Safety at Work (Hazardous Substances—Reduced Secondary Containment for Certain Above Ground Stationary Tanks) Safe Work Instrument 2017

infostore.saiglobal.com

SwRI 95-03

Testing Requirements for Multi Hazard Protected Aboveground Flammable Liquid/Fuel Storage Tanks

Health and Safety at Work (Hazardous Substances—Reduced Secondary Containment for Certain Above Ground Stationary Tanks) Safe Work Instrument 2017

infostore.saiglobal.com

UL 2085

Standard for protected Aboveground Tanks for Flammable and Combustible Liquids issued 01 December 1999

Health and Safety at Work (Hazardous Substances—Reduced Secondary Containment for Certain Above Ground Stationary Tanks) Safe Work Instrument 2017

http://www.shopulstandards.com/

AS/NZS 3845:1999

Road safety barrier systems

Health and Safety at Work (Hazardous Substances—Thermoplastic Stationary Tanks) Safe Work Instrument 2017

https://www.standards.govt.nz/

BS EN 1778:2000

Characteristic values for welded thermoplastics constructions - Determination of allowable stresses and moduli for design of thermoplastics equipment

Health and Safety at Work (Hazardous Substances—Thermoplastic Stationary Tanks) Safe Work Instrument 2017

https://shop.bsigroup.com/

BS EN 12573-1:2000

Welded static non-pressurized thermoplastic tanks – Part 1: General principles

Health and Safety at Work (Hazardous Substances—Thermoplastic Stationary Tanks) Safe Work Instrument 2017

https://shop.bsigroup.com/

BS EN 12573-2:2000

Welded static non-pressurized thermoplastic tanks – Part 2: Calculation of vertical cylindrical tanks

Health and Safety at Work (Hazardous Substances—Thermoplastic Stationary Tanks) Safe Work Instrument 2017

https://shop.bsigroup.com/

BS EN 12573-3:2000

Welded static non-pressurized thermoplastic tanks – Part 3: Design and calculation for single skin rectangular tanks

Health and Safety at Work (Hazardous Substances—Thermoplastic Stationary Tanks) Safe Work Instrument 2017

https://shop.bsigroup.com/

BS EN 12573-4:2000

Welded static non-pressurized thermoplastic tanks – Part 4: Design and calculation of flanged joints

Health and Safety at Work (Hazardous Substances—Thermoplastic Stationary Tanks) Safe Work Instrument 2017

https://shop.bsigroup.com/

DVS 2203

Testing of welded joints between panels and pipes made of thermoplastics

Health and Safety at Work (Hazardous Substances—Thermoplastic Stationary Tanks) Safe Work Instrument 2017

https://global.ihs.com/

UL 142

Standard for Steel Above Ground Tanks for Flammable and Combustible Liquids, ninth edition, dated December 28, 2006

Health and Safety at Work (Hazardous Substances—Above Ground Stationary Tanks Connected to a Generator Set) Safe Work Instrument 2017

http://www.shopulstandards.com/

BS 799-5:2010

Oil burning equipment – Part 5: Carbon steel oil storage tanks – Specification

Health and Safety at Work (Hazardous Substances—Above Ground Stationary Tanks Connected to a Generator Set) Safe Work Instrument 2017

https://shop.bsigroup.com/

OFS T200 - Oil Firing Equipment Standard

Steel oil storage tanks and tank bunds for use with distillate fuels, lubrication oils and waste oils, Issue 6, 2007

Health and Safety at Work (Hazardous Substances—Above Ground Stationary Tanks Connected to a Generator Set) Safe Work Instrument 2017

https://www.thenbs.com/PublicationIndex/documents/details?Pub=OFTEC&DocID=292780

AS/NZS 1170.0:2002

Structural design actions – Part 0: General principles

Health and Safety at Work (Hazardous Substances – Above Ground Rotationally-Moulded Polyethylene Stationary Tanks) Safe Work Instrument 2017

https://www.standards.govt.nz/

AS/NZS 1170.1:2002

Structural design actions – Part 1: Permanent, imposed and other actions

Health and Safety at Work (Hazardous Substances – Above Ground Rotationally-Moulded Polyethylene Stationary Tanks) Safe Work Instrument 2017

https://www.standards.govt.nz/

AS/NZS 1170.2:2011

Structural design actions – Part 2: Wind actions

Health and Safety at Work (Hazardous Substances – Above Ground Rotationally-Moulded Polyethylene Stationary Tanks) Safe Work Instrument 2017

https://www.standards.govt.nz/

AS/NZS 1462.6:2008

Methods of test for plastics pipes and fittings: Method 6: Thermoplastics pipes, fittings and assemblies for the transport of fluids under pressure — Resistance to internal pressure

Health and Safety at Work (Hazardous Substances – Above Ground Rotationally-Moulded Polyethylene Stationary Tanks) Safe Work Instrument 2017

https://www.standards.govt.nz/

AS/NZS 4766:2006

Polyethylene storage tanks for water and chemicals

Health and Safety at Work (Hazardous Substances – Above Ground Rotationally-Moulded Polyethylene Stationary Tanks) Safe Work Instrument 2017

https://www.standards.govt.nz/

AS/NZS ISO 9001:2008

Quality management systems – requirements

Health and Safety at Work (Hazardous Substances – Above Ground Rotationally-Moulded Polyethylene Stationary Tanks) Safe Work Instrument 2017

https://www.standards.govt.nz/

ASTM D2837-13e1

Standard test method for obtaining hydrostatic design basis for thermoplastic pipe materials or pressure design basis for thermoplastic pipe products

Health and Safety at Work (Hazardous Substances – Above Ground Rotationally-Moulded Polyethylene Stationary Tanks) Safe Work Instrument 2017

https://www.astm.org/

ASTM D638-14

Standard Test Method for Tensile Properties of Plastics

Health and Safety at Work (Hazardous Substances – Above Ground Rotationally-Moulded Polyethylene Stationary Tanks) Safe Work Instrument 2017

https://www.astm.org/

ASTM D2765-16

Standard test methods for Determination of Gel Content and Swell Ratio of Crosslinked Ethylene Plastics

Health and Safety at Work (Hazardous Substances – Above Ground Rotationally-Moulded Polyethylene Stationary Tanks) Safe Work Instrument 2017

https://www.astm.org/

ASTM D1505-10

Standard Test Method for Density of Plastics by the Density-Gradient Technique

Health and Safety at Work (Hazardous Substances – Above Ground Rotationally-Moulded Polyethylene Stationary Tanks) Safe Work Instrument 2017

https://www.astm.org/

ASTM D2990-09

Standard test methods for tensile, compressive, and flexural creep and creep-rupture of plastics

Health and Safety at Work (Hazardous Substances - Above Ground Rotationally-Moulded Polyethylene Stationary Tanks) Safe Work Instrument 2017

https://www.astm.org/

BS EN 1778:2000

Characteristic values for welded thermoplastics constructions - determination of allowable stresses and moduli for design of thermoplastics equipment

Health and Safety at Work (Hazardous Substances – Above Ground Rotationally-Moulded Polyethylene Stationary Tanks) Safe Work Instrument 2017

https://shop.bsigroup.com/

ISO 527-1:2012 – Plastics – Determination of tensile properties – Part 1: General principles and ISO 527-2:2012 – Plastics – Determination of tensile properties – Part 2: Test Conditions for moulding and extrusion plastics

Health and Safety at Work (Hazardous Substances – Above Ground Rotationally-Moulded Polyethylene Stationary Tanks) Safe Work Instrument 2017

https://www.iso.org

ISO 899-1:2003 – Plastics – Determination of creep behaviour – Part 1: tensile creep and ISO 899-2:2003 – Plastics – Determination of creep behaviour – Part 2: Flexural creep by three-point loading

Health and Safety at Work (Hazardous Substances – Above Ground Rotationally-Moulded Polyethylene Stationary Tanks) Safe Work Instrument 2017

https://www.iso.org

ISO 1183-1:2012 Plastics – Methods for determining the density of non-cellular plastics – Part 1: Immersion method, liquid pyknometer method and titration method, ISO 1183-2:2004 Plastics – Methods for determining the density of non-cellular plastics –

Part 2: Density gradient column method and ISO 1183-3:1999 Plastics – Methods for determining the density of non-cellular plastics – Part 3: Gas pyknometer method

Health and Safety at Work (Hazardous Substances – Above Ground Rotationally-Moulded Polyethylene Stationary Tanks) Safe Work Instrument 2017

https://www.iso.org

ISO 9080:2003 Plastics piping and ducting systems – Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation

Health and Safety at Work (Hazardous Substances – Above Ground Rotationally-Moulded Polyethylene Stationary Tanks) Safe Work Instrument 2017

https://www.iso.org/standard/28314.html

NZS 1170.5:2004 Structural design actions, Part 5: Earthquake actions – New Zealand

Health and Safety at Work (Hazardous Substances – Above Ground Rotationally-Moulded Polyethylene Stationary Tanks) Safe Work Instrument 2017

https://www.standards.govt.nz/

NZS 3101:Part 1:2006 Concrete structures standard and NZS 3101:Part 2:2006 Concrete structures standard

Health and Safety at Work (Hazardous Substances – Above Ground Rotationally-Moulded Polyethylene Stationary Tanks) Safe Work Instrument 2017

https://www.standards.govt.nz/

These standards are available for inspection, free of charge, between the hours of 9.00am and 5.00pm from Monday to Friday (excluding statutory holidays) at WorkSafe New Zealand located at Level 6, 86 Customhouse Quay, Wellington 6011.

You may also contact WorkSafe using the following email to arrange to view the material incorporated by reference: Regulatory.Frameworks@worksafe.govt.nz

Dated at Wellington this 7th day of December 2017.

NICOLE ROSIE, Chief Executive, WorkSafe New Zealand.